CV, Romanian Mechanical Supervisor in Qatar looking worldwide.

Available
Serial No: 18294
Skills keywords: 
Current location:  Qatar - View on map
Nationality: Romanian
Spoken languages: enghlis

WORK EXPERIENCE

MECHANICAL SUPERINTENDENT(24.07.2014-PRESENT)

Company:DESCON ENGINEERING L.L.C.-QATAR

Company activity field: :OIL&GAS INDUSTRY

Responsibilities:The project is:Shut-Down & Maintenance

Qatar Gas:Ras Laffan/Dolphin/MIC/Olefin Q-chem

Maintenance dynamic equipment:compressors,pumps,fans

Participating in inspection and maintenance of all rotating equipment

Participating troubleshooting activities associated with unplanned shutdowns, in collaboration with the maintenance supervisors & reliability engineer

Worked with preventive and corrective maintenance planning and scheduling for

rotating equipment.Supervising the contractor maintenance works.Checking the final

flanges aliqnment ofn suction of discharge side after the piping works are finished.

Inspecting the journal bearings and the axial bearings,mechanical seals both sides,lube oil system gas seal system.Fitting the cupling hub on the compressor/pump,shaft and performing the final aliqnment between the compressor or pump and motor.I worked with:ABC-piston compressor,and performing CM/PM maintenance for Siemens centrifugal compressor and Elliott steam turbine.Worked with documentation according API(616/617/686)for rotating equipment

MECHANICAL.TECHNICIAN-SUPERVISOR (10.10.2013-28.03.2014)

Company:AL JABER ENERGY SERVICES-UAE/TECHINT-UAE-CONSORTIUM

Company activity field:OIL&GAS INDUSTRY

Responsibilities:The project is in Ruwais – RHST-2 GASCO UAE

Pre-commissioning dynamic equipments/install/maintenance for:compressors,fans,pumps.

Commissioning and start-up dynamic equipments.

Responsibilities line technique in performing repairs and accidental to axial compressors, propane compressors, compressors hydrogen sulphide

Involved in routine tasks, such as lubrication of machinery, seal replacement, cleaning of parts during an overhaul and preventive maintenance.

– Detect accidental shutdowns causes and remedies.

Works with rotating equipment:screw compressor Sinergia/Nuovo Pignone

Performing and teaching the local techniciens compressor aliqnment with SKF

Laser kit(tksa20-40)Works with water pump:Sulzer/Ebara/Flowserve.

Solo run,functional test for rotating equipment and monitoring the vibration spectrum.

Working with the technical documentation accordingAPI(616/617 for rotating equipment)

and ASME standards

MECHANICAL.TECHNICIAN-SUPERVISOR(23.11.2012-20.03.2013)

Company:FOUR QUEST ENERGY-FOR UAE/GASCO

Company activity field:OIL&GAS INDUSTRY

Responsibilities: The project is-Ruwais NGL4-Petrofac JV-UAE

Detection pipe lines after reading isometric drawing and their preparation for hydrotest.Hydrotest activities using tools as:

-chart recorder for pressure

-chart recorder for temperature

-manifold

-hoses

Responsibilities:Commissioning rotating – Commissioning of dynamic equipment & maintenance

– Mounting position dynamic equipment

– Checking elevation and alignment

– Check horizontality and verticality static equipment

– Checking the oil for dynamic machines

– Checking documentation commissioning of dynamic equipment

I did, alignments, with dial indicator and parallel to the flange, also oil changes and rotation pumps

Undertaking all mounting, elevation, alignment using dial indicator , repairs, pre-commissioning, commissioning, preventive maintenance including lubrication of machinery and condition monitor pertaining to rotating machinery, such as:

– Centrifugal gas compressors, reciprocating compressors, screw compressors;

– gas turbines, blowers, agitators

– Centrifugal, screw, gear, lobes pumps, canned pump, dosing pump, submersible pump

Working in accordance with commissioning procedures for rotating equipment, implemented by the company. Responsibilities line technique in performing repairs and accidental to gas and steam turbines, axial compressors, propane compressors, compressors hydrogen sulphide.

MILLWRIGHT/MECHANICAL TECHNICIAN (09.08.2010 – 20.05.2012)

Company: IREM S.P.A. (Italy)

Company activity field :OIL&GAS INDUSTRY

Responsibilities:The project was: refinery expansion Elefsina-Greece

I worked as a :millwright steel structures and mechanical/technician commissioning & maintenance. I assembled and installed modules with fans for cooling industrial water.

Or use steel elements (beams, bolts, washers, nuts) was all mechanical installation.

In these four months I worked as a millwright, I worked with pumps and compressors.

I did, alignments, with dial indicator, and parallel to the flange, also oil changes and rotation pumps. Finally, the last time, I did part of pre-commissioning team, and participated in all activities linked to this procedure:

-hydrotest the pipe and valve paths.

-tests with air and gas

-washing with water, and air blowing, the route after completion, test pressure.

-centering gaskets between the flanges, center, bolts to be equal, the final gathering, key, torque.

Responsibilities:Commissioning rotating dynamic equipment & maintenance

Supervising the activities of repair, maintenance and service, installation and commissioning for dynamic equipment (pumps, turbines, compressors, fans, etc..)

Supervising the activities of repairing, maintenance and service, installation and commissioning for dynamic equipment (pumps, turbines, compressors, fans etc)

Replacing different parts of the machine or adjust clearances and alignment of their moving parts;

Aligning machines and equipment, using hoists, jacks, hand tools, squares, rules, micrometers, plumb bobs or dial indicator and laser system;

Involved in routine tasks, such as lubrication of machinery, seal replacement, cleaning of parts during an overhaul and preventive maintenance.

– Detect accidental shutdowns causes and remedies.

SUPERVISOR/MECHANICAL TECHNICIAN (15.07.2008 – 15.07.2010)

Company: DANFOSS GROUP

Company activity field : Production modules, thermal.

Responsibilities:Mechanic maintenance/installation.

I dealt with assembly, thermal modules, and assembly of heat exchangers, brazed plate.

Also the assembly, gauges for measurement of, the water pressure.

Install safety valve, then, did the water pressure test to see if there are holes, welding, in order to remedy existing defects.

SUPERVISOR/MECHANICALTECHNICIAN(02.09.2007 – 14.07.2008)

Company: RUUKKI-ROMANIA

Company activity field :Production: Building components for industrial halls

Responsibilities:Mechanic maintenance/installation

I worked as a mechanic maintenance/repairs.

More specifically, I deal with maintenance, repair, conveyor belts, and presses for, laminated board.

Central rolls from band conveyors, presses watching oil level

Making intervention works to prevent and eliminate possible emergency situations (greasing the bearings, coupling and motor-pump assembly balance and others).

Repair and maintenance of machine tools in society

MECHANICAL TECHNICIAN (27.08.1983 – 15.08.2006)

Company: S.C. CAROM S.A. and RAFO ONESTI

Company activity field :Oil &Gas Industry

Petrochemical industry

Responsibilities:Mechanic Commissioning rotating & maintenance

I worked on these two companies

I worked as a mechanic / technician for dynamic machines that:

-nitrogen compressors, air technology, AMC air, oxygen

-pumps: water, oxygen

-air and steam turbines

I deal with maintenance and repair, such machines, as well as installation and putting into operation.

There compressors, 2 stage, 4 stage, and the membrane inlet and outlet valves.

I deal with the exchange of these valves, the oil change, and the alignment (with watches comparators), pumps, and parallel flanges.

Also make revisions on all routes of industrial water, steam networks, it replaced the valves and gaskets, screws and bolts.

I was busy with activity, pre-commissioning and commissioning, putting pressure water pipes, washing them with chemicals, and blowing air. Each year is made, review, is replaced, valves, bolts, fittings, and pipe routes, if they were corroded.

I did review, the heat exchangers, installations, washed with water and blowing air..

As a complementary activity, I deal with control of water, and steam pressure gauges to check the index, real pressure.

I participated in reviewing the steam network, I changed gaskets, asbestos, and valves, on trails, steam.

Also, one time I worked at the workshop, mechanics, where I deal with the correction, compressor valves, and mounting them.

I was busy, and chlorination station, industrial water.

More precisely, lies in water, chlorine, zinc sulphate for water purification.

Performing maintenance and repairing activities repair for blowers, fans, gear boxes, gas turbines, reciprocating, centrifugal compressors, piston pumps, single – and multi-stage centrifugal pumps, metering pumps.

Performing alignment, using dial indicator, commissioning, start-up, maintenance and repairing for the rotating equipment as follows: gas and steam turbines, pumps and compressors.

Support maintenance team on preventive and predictive maintenance process, ensuring risk of failures are fully detected, understood and mitigated.

Support the implementation of reliability projects in rotating equipment to increase plant availability

Ensuring compliance and proper content of Predictive Maintenance program; makes revisions as necessary based on conditions. Includes all aspects of the machines incl. coolers, filters, checks valves, control systems, alarm and shut down systems, oil systems, calibration and functionality

Participating in inspection and maintenance of all rotating equipment

Participating troubleshooting activities associated with unplanned shutdowns, in collaboration with the maintenance supervisors & reliability engineer

Involved in periodical revisions and overhauling activities

EDUCATION

Studies: High School College(mechanical) class: 1983

Certificates & awards :Inspector health & safety

ABILITIES: Alignment with laser system SKF-TKSA 20/40 rotating equipment(pump,compressor)

Alignment for blade fans(angular)

Overhaul and maintenance rotating equipment(API-616,617,610)

Verification and inspection :mechanical seals,bearings rotating eguipment

Foreign Languages(Knowledge level):

english (medium)

Italian(medium)

PC Skills:

have knowledge of PC operating

 

 

 

 

 






popup-img